• Nine Gesture Recognition Modes: Includes Up, Down, Left, Right, Push, Pull, CW, CCW, and Wave gestures.
• High Gesture Speed: Gesture speed ranges from 60°/s to 600°/s in Normal Mode and 60°/s to 1200°/s in Gaming Mode.
• Proximity Detection: Built-in proximity detection for improved performance.

• Wide Detection Range: 120°/180° detection angle with a range of up to 12 meters (± 2m)
• Adjustable Settings: Ambient light sensitivity and time-delay (5 seconds to 12 minutes) can be adjusted
• High Load Capacity: Suitable for 500W resistive load (e.g., incandescent lamps) and 150W inductive load (e.g., LED, energy-saving lamps)
• Weatherproof Design: IP44 rated, ideal for both indoor and outdoor use

• 4-digit 7-segment LED display with a super red color for clear visibility
• Common anode configuration for easy integration into various DIY projects
• Ideal for use in clocks, timers, and other time-based applications
• Compact size of 0.36 inches, perfect for space-constrained setups

• Ambient Light Cancellation: Filters out ambient light interference for accurate readings
• High Sample Rate: Capable of fast data output
• Efficient Power Use: Low power consumption with a voltage range of 1.8V to 3.3V
• Compact Design: Small and lightweight for easy integration into various projects

The ADXL345 is a compact, ultralow power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. It offers digital output data formatted as 16-bit two's complement, accessible through either SPI (3- or 4-wire) or I2C digital interface. Ideal for mobile device applications, it measures static and dynamic accelerations.

• High resolution (13-bit) measurement up to ±16 g.
• Supports both SPI (3- or 4-wire) and I2C digital interfaces.
• Low power consumption for mobile applications.
• Compact design for easy integration.
• Includes special functions like activity/inactivity monitoring, tap detection, and free-fall detection.

• 16-bit bidirectional I/O expansion for microcontrollers
• Supports I2C (MCP23017) up to 1.7 MHz and SPI (MCP23S17) up to 10 MHz
• Configurable interrupt system with INTA & INTB pins
• Three hardware address pins allow up to 8 devices on the same bus

• Magnetic encoder induction angle sensor
• Wide operating temperature range: -40°C to 125°C
• Low power consumption with 3.3V DC power supply
• Compact size, ideal for various applications

• Ideal for driving stepper motors with ease
• Compact and efficient design
• Low power consumption
• Simple to interface with Arduino or other microcontrollers

• Input Voltage Range: 4V - 35V
• Output Voltage: Adjustable from 1.25V to 25V
• Output Current: Up to 3A Max (requires heat sink if >15W)
• CC Range: 0-2A (Adjustable)

• Chipset: TI CC2530 chipset for reliable wireless communication.
• Voltage Range: DC 2.1V ~ 3.6V (recommended 3.3V for optimal performance).
• Transmission Distance: Up to 800 meters (with 3dBi antenna in open space).
• Antenna Interface: SMA interface for connecting antennas.

• Compact Display: 1.8-inch size for portable projects
• High Resolution: 128x160 pixels for clear images
• Wide Viewing Angle: Improved visibility from various angles
• Controller: ST7735, widely used for high-quality displays

• Accurate temperature and humidity sensing
• I2C and one-wire bus communication
• Wide temperature measurement range (-40°C to 125°C)
• Compact and easy to integrate with Arduino

• High-precision TDS measurement for water quality testing.
• Compatible with Arduino and other microcontrollers for easy integration.
• Low power consumption with a working current of just 3-6mA.
• Wide measurement range from 0 to 1000ppm.

• Motor drive module comes with four L9110S chips
• Supports 4 DC motors or two 4-wire 2-phase stepper motors
• Supply voltage: 2.5V - 12V
• Maximum operating current: 0.8A

• Dot Laser for precise applications
• Low Power Consumption at 5mW
• Compact Design with a 6mm OD for easy integration
• Stable Operation at a 650nm wavelength

The Ublox NEO-6M GPS Module offers high precision and sensitivity, making it ideal for various applications, including cars and other mobile setups. Key features include:

• High precision binary output
• High sensitivity for indoor applications
• Battery for power backup
• EEPROM for storing configuration settings
• Flexible mounting with ufl cable connected antenna
• Serial TTL output with four pins: TX, RX, VCC, and GND
• Configurable from 4800 Baud to 115200 Baud rates (default 9600)
• Cold start time: 38s, Hot start time: 1s
• SuperSense ® Indoor GPS: -162 dBm tracking sensitivity
• Operating temperature: -40 to 85°C
• 5Hz position update rate
• UART TTL socket
• Dimension: 22x30x13 mm
• Weight: 12g